Skip to main content

IIS SMTP Server Pickup Test



 Recently when deploying an IIS SMTP server, i needed to test with a simple email. Putting the below in a text document in the mail pickup folder under inetpub will perform a test and send the email out. 


The to address can be anyone and the from address should be the domain you are trying to send from. If using a connector in M365 you can masquerade as any email address, If you are using authentication, you will need to set the From address as the account you are authenticating with 

Comments

Post a Comment

Popular posts from this blog

Removing Multiple Datastores From Single ESXI Host Via PowerCLI

This post covers removing a multiple datastores from a single host at a time in vCenter with the use of PowerCLI. In the case where you have multiple hosts which have MANY MANY Datastores attached, its important to make sure you fully unmount and detach the DS from the host before removing storage connections.  Below is the code to make this happen $datastores = 'DS1','DS2'  $startTime = Get-Date $esxName = 'vmh.local' foreach($datastoreName in $datastores){ $datastoreName  $esx = Get-VMHost -Name $esxName $ds = Get-Datastore -Name $datastoreName $canonicalName = $ds.ExtensionData.Info.Vmfs.Extent[0].DiskName $storSys = Get-View $esx.Extensiondata.ConfigManager.StorageSystem $device = $storsys.StorageDeviceInfo.ScsiLun | where {$_.CanonicalName -eq $canonicalName} if($device.OperationalState[0] -eq 'ok'){     $StorSys.UnmountVmfsVolume($ds.ExtensionData.Info.Vmfs.Uuid) } $storSys.DetachScsiLun($device.Uuid) } $endTime = Get-Date $executionTime = $endTime...
Post a Comment
Read more

HPE DL Series Host TPM Attestation Alarm Remediation

  Recently in my lab, i ran into an issue with the Host TPM Attestation Alarm being set. This was a little annoying that out of the box there are some configuration items that are not done by standard, and this guide will cover the specific BIOS / RBSU Configs that need to be made to clear this up.  First off, we need to boot into the BIOS / System Config / RBSU, so unfortunately you need to reboot your host - none of these changes can be made through the ILO "I reboot now - Good luck everybody else"  Next up, we need to navigate to Server Security and Secure Boot Settings  Next up, Select "Attempt Secure Boot" and accept the warning regarding the required reboot.  Navigate back to the main "Server Security" Menu and Select Trusted Platform Module Options  Ensure you have the below Config:  Current TPM Type: TPM 2.0  Current TPM 2.0 Active PCRs: SHA256 Only  TPM 2.0 Operation: No Action UNLESS your current TPM Type is not 2.0 - change to TPM ...
Post a Comment
Read more

Deploying CEPH in the homelab

I recently rebuilt my Ceph lab to more closely mirror a real production deployment, rather than the usual - it works but don’t look too closely lab setups. The goals were simple but non-negotiable: 3 MONs (odd quorum) 2 MGRs (HA control plane) Host-level fault domain Replication size = 3 RGW (S3) only — no CephFS, no RBD Clean DNS (no /etc/hosts hacks) This post walks through the exact process I used to deploy a clean, repeatable Ceph RGW cluster using cephadm on Ubuntu, with explicit placement control and zero surprises. 🧠 Cluster Design – Nodes & IPs Monitor / Manager Nodes (Control Plane) ceph-mon01 — MON + MGR — 172.16.1.81 ceph-mon02 — MON + MGR — 172.16.1.82 ceph-mon03 — MON + MGR — 172.16.1.83 RGW (S3 Gateway) ceph-rgw01 — RGW Gateway — 172.16.1.86 OSD Storage Nodes ceph-osd01 — OSD Node (6 × 80 GB disks) — 172.16.1.91 ceph-osd02 — OSD Node (6 × 80 GB disks) — 172.16.1.92 ceph-osd03 — OSD Node (6 × 80 GB disks) — 172.16.1.93 📋 Cluster Requirements ...
Post a Comment
Read more